起重機港口機械專業詞彙

❶ 港口機械，什麼是港口機械

港口機械主要指的是港口的岸邊吊機，包括門座式起重機，岸橋式起重機，連續式卸船機，移動式卸船機，連續式裝船機等，還包括集裝箱裝卸橋。港口機械還包括後方堆場專用設備，例如集裝箱碼垛機等。

❷ 什麼是港口起重機械他分哪些類型

港口起重機就是將貨物由碼頭岸邊往船上吊裝或者由船上往碼頭岸邊卸貨的機械設備，一般分為岸橋式、門座式、斗輪連續式等幾種類型。

❸ 港口起重機

5000.Q4起重機操作證

❹ 機械類專業詞彙翻譯

樓上的翻譯得可以
不過個別有錯，列出如下：
1.Process Water and Waste Piping工業污水排放管道系統
註：工藝用水及其廢水管道
2.Humidity Control Equipment適度控制設備
註：濕度調節設備
3.Breechings, Chimneys, and Stacks 煙道管,煙囪和堆棧
註：煙囪、分叉管和爐身
4.HVAC Instrumentation and Controls高壓(空調)儀表和控制設備
註：HVAC指的是：Heating, Ventilating, and Air Conditioning Equipment供熱通風與空氣調節設備
5.Testing, Adjusting, and Balancing 檢測,調整和均衡系統
註：測試、調整和平衡校正

以下為本人的翻譯
Mechanical機械的
Mechanical Hangers and Supports 機械 吊支架
Mechanical Sound, Vibration, and Seismic Control機械 聲音、震動和地震控制
Mechanical Identification機械 鑒別
Mechanical Insulation機械 絕緣
Building Services Piping建築管道系統和配件
Pipes and Tubes管道
Valves閥門
Piping Specialties特殊管道
Pumps泵
Domestic Water Piping生活用水管路
Deionized Water Systems去離子水系統
Sanitary Waste and Vent Piping生活廢水及其排泄管路
Storm Drainage Piping雨水排泄管路
Heating and Cooling Piping加熱及製冷管路
Process Air and Gas Piping工藝空氣及工藝廢氣管路
Process Water and Waste Piping工藝用水及廢水管路
Fire Protection Piping消防管路
Plumbing Fixtures and Equipment廁、浴間設備及管路
Plumbing Fixtures廁、浴間設備
Plumbing Pumps污水泵
Potable Water Storage Tanks飲用水存儲罐
Domestic Water Conditioning Equipment生活用水溫度調節設備
Domestic Water Filtrating Equipment生活用水過濾設備
Domestic Water Heaters生活用水加熱器
Furnaces爐
Fuel-Fired Heaters燃料加熱器
Breechings, Chimneys, and Stacks煙囪、分叉管和爐身
Refrigeration Equipment製冷設備
Refrigeration Compressors製冷壓縮機
Refrigerant Monitoring Systems製冷監控系統
Refrigerant Condensing Units製冷冷凝機組
Packaged Water Chillers集成冷水機
Liquid Coolers and Evaporative Condensers液體冷卻器和蒸發冷凝器
Heating, Ventilating, and Air Conditioning Equipment供熱通風與空氣調節設備
Heat Exchangers換熱器
Air Handling Units空氣調節單元
Heat Pumps熱泵
Humidity Control Equipment濕度控制設備
Terminal Heating and Cooling Units終端加熱及製冷單元
Ducts (Sheet Metal)管道（鐵皮圍成）
Fans風扇
Air Outlets and Inlets空氣進出口
HVAC Instrumentation and Controls HVAC控制裝置
Pneumatic and Electric Controls氣動和電動控制
Building Systems Controls建築系統控制
Direct Digital Controls直接數字控制
Sequence of Operation操作程序
Testing, Adjusting, and Balancing測試、調整和平衡校正

❺ 港口機械主要包括哪些

fdjhtdjh港口抄經營襲是指港口經營人在港口區域內為船舶、旅客和貨物提供港口設施或者服務的活動，主要包括下列各項業務：一為船舶提供碼頭、過駁錨地、浮筒等設施；二為旅客提供侯船和上下船舶設施和服務；三為委託人提供貨物裝卸（含過駁）、倉儲、港內駁運、集裝箱堆放、拆拼箱以及對貨物及其包裝進行簡單加工處理等；四為船舶進出港、靠離碼頭、移泊提供頂推、拖帶等服務；五為委託人提供貨物交接過程中的點數和檢查貨物表面狀況的理貨服務；六為船舶提供岸電、燃物料、生活品供應、船員接送及提供垃圾接收、壓艙水（含殘油、污水收集）處理、圍油欄供應服務等船舶港口服務；七從事港口設施、設備和港口機械的租賃、維修業務。

❻ 請教懂港口起重機英語的高手指教！

Rated starting weight: under spreader: 30.5 tons
Beam under the hook: 35 tons
Self: About 545 tons
Reach distance: 35.5 meters
Extension distance: 11 meters
Carts gauge: 16 meters
Based distance: 18 meters (the same track centerline distance between the two bearings)
Lifting Height: track: track 25 meters as follows: 12 meters
Overall width: 29 meters
Total height: 71 meters
Big wheels a few: (all / Driver) 32 / 8
The largest round of pressure: 40.6 tons / round
Or 50-speed from 120 meters / min
Vehicle maximum speed: 150 m / min
Carts maximum speed: 45 m / min
Spreader: 20'-40 'telescopic spreader.
About mping: ± 5 °
Before and after the mp: ± 5 °
Wire Rope Specifications: 22.4 mm pitch from 30mm or 16mm anti-sway 11mm car
High Voltage Power Supply: AC 3KV 50HZ
Electronic control:
1 # machine in July 2006 were electrical transformation, the use of GE 9030 PLC control, since l / carts, cars drive the use of ABB drives; PLC and drive communication between the use of PROFIBUS; remote control the use of GE's Genus means of communication. Lifting motor power: 310KW; car motor power: 80KW; carts Motor Power: 25KW * 4; pitch motor power: 75KW.
2 # machine in October in 99 years to transform the electrical, the GE 9030 PLC control, since l / carts, the use of TE's RTV84 car drives drive; remote control of the use of GE means of communication Genus. Lifting motor power: 310KW; car motor power: 80KW; carts Motor Power: 25KW * 4; pitch motor power: 75KW

❼ 求起重吊車常用術語中英對照

起升機構 Hoisting Mechanism
變幅機構 Luffing Mechanism
回轉機構 Swing Mechanism
合格證明 Conformity Certificate
試驗報告 Test Report
製造單位 Manufacture Company
設計單位 Design Institute
型式 Type
型號 Model
規格Specification
編號 Serial No.
樣機 Sample Vehicle
基本臂 Basic Jib
主臂 Main Jib
吊臂 Suspension Arm
支腿 Outrigger
主鉤 Main Hook
空載 Idle Load
滿載 Full Load
起臂 Rise Arm
落臂 Descend Arm
伸臂 Extend Arm
縮臂 Retract Arm
回轉速度 Rotating Speed
總長 Total Length
總寬 Total Breadth
總高 Total Height
軸距 Wheelbase
輪距 Tread
前懸 Front Overhang
後懸 Rear Overhang
前伸 Front Protraction
後伸 Rear Protraction
接近角 Approach Angle
離去角 Departure Angle
最小轉彎直徑 Minimum Diameter Of Turning Circle
最小離地間隙 Minimum Ground Clearance
前軸 Front Axle
後軸 Rear Axle
底盤 Chassis
軸數 Number Of Axles
驅動型式 Driving Type
排量 Swept Volume
最大扭距 Maximum Torque
排氣管 Exhaust Pipe
發動機 Engine
變速器 Speed Changer
前進檔 Forward Gears
離合器 Clutch
速比 Speed Ratio
主減速比 Final Ratio
轉向器 Redirector
轉向型式 Steering Type

制動系統 Braking System
制動力 Brake Force
車身 Vehicle Body
油泵 Oil Pump
起升馬達 Hoisting Motor
回轉馬達 Swing Motor
回轉支承 Pivoting Support
變幅缸 Amplitude Cylinder
伸縮缸 Telescoping Cylinder
支腿缸 Outrigger Cylinder
上車操縱閥 Aboard Control Valve
取力器 Power Takeoff
吊鉤 Crane Hook
鋼絲繩 Steel Wire Rope
力矩限制器 Load Moment Limiter
吊臂 Suspension Arm
許用應力值 Allowable Stress Value
溢流閥 Overflow Valve
臂架 Arm Suppor T
主桿 Main Post
潤滑油 Lubricating Oil
潤滑脂 Grease Lubricant
液壓油 Hydraulic Oil
地磅 Loadometer
酒精 Alcohol
丙酮 Acetone
打磨機 Polisher
接線板 Terminal Board
萬用表 Multi-Meter
封存 Seal Up For Keeping
自檢報告 Self-Check Report
合格證明 Conformity Certificate
力矩限制器檢測報告 Load Moment Limiter
高度限位器 Height Limitator
水平儀 Gradienter
風速儀Anemoscope
工作機構 Working Mechanism
操縱機構 Control Mechanism
電氣和控制系統 Electrical And Control System
滑輪 Pulley
吊具 Hanger
高強度螺栓 High Strength Bolt
主要總成明細表 Principal Assembly List

手拉葫蘆
hand chain hoist

手拉葫蘆例句
Upside-down method using hand chain hoist for the installation of steel oil tank with an inner floating drum
手拉葫蘆提升倒裝法制安內浮頂鋼制油罐

冶金起重機
metallurgical crane

冶金起重機
Application of 3D hook positioning and measuring device to metallurgical crane
吊鉤三維定位檢測裝置在冶金起重機上的應用
The application of bearing with inserted graphite to large metallurgical crane
鑲嵌石墨軸承在大型冶金起重機上的應用

運行式起重機：
TRAVELLING CRANE

運行式起重機例句：
AutoCAD based TRAVELLING CRANE design system
基於AutoCAD的運行式起重機設計系統

輪胎起重機
wheel crane或tyre crane
輪胎起重機例句
Design of Gearbox in Travel Par Wheel Crane
輪胎起重機行走部分變速箱的設計
The Parametric Structure Calculation and Analysis Platform of Lattice Mobile Port Tyre Crane
格構式動臂港口輪胎起重機結構參數化計算分析平台

防爆起重機
explosion-proof crane

防爆起重機例句
Further Improvement on Explosion-Proof Crane
防爆起重機的進一步完善

夾鉗起重機
crane with tongs或clamping crane或soaking-pit crane

夾鉗起重機英語
INNOVATION DESIGN FOR THE CRANE WITH TONGS
夾鉗起重機(鉗吊)的更新改造設計
Cracks have been observed on clamp arms of an imported 94t electric clamping crane after 4 years of service.
從國外購買的94t電動式夾鉗起重機，在使用4年後夾鉗鉗臂產生裂紋。
The clamping device of soaking-pit crane
夾鉗起重機的夾鉗裝置

移動式起重機
mobile crane或traveling crane
移動式起重機英文
The rental rates investigation of global mobile cranes of 2008

❽ 港口機械專業英語

一樓給你的是買書信息

我給你個網址 這里可以下載到機械英語專業詞彙手冊 你自己下載吧

❾ 物料搬運機械的常用詞彙

千斤頂 jack
叉車 fork lift truck
小車式輸送機 cartype conveyor
手動葫蘆 hand chain block and lever
手推車 hand truck
斗式提升機 bucket elevator
斗輪挖掘機 bucket wheel excavator
斗輪堆取料機 bucket wheel staker-reclaimer
水力輸送裝置 hydraulic transport
平地機 grader
平衡重式叉車 counter balanced fork lift truck
吊鉤 lifting hook
多斗挖掘機 multibucket excavator
自行式起重機 self-propelled crane
自動人行道 moving sidewalk
自動扶梯 escalator
抓鬥 grab
刮板輸送機 scraper conveyor
升降台 lifting table
板式輸送機 slat conveyor
門座起重機 portal crane
架空索道 aerial ropeway
架空單軌系統 overhead monorail system
埋刮板輸送機 enmasse conveyor
容器式管道輸送裝置 capsule-tube transport system
振動輸送機 vibrating conveyor
料斗升降機 skip hoist
氣墊搬運裝置 air cushion transporter
浮游起重機 floating crane
起重吸盤 hoisting suctorial cup
起重滑車 hoisting tackle
起重機夾軌器 crane rail clamp
起重機軌道 crane railway
起重機錨定器 crane anchor
高架倉庫 high rack warehouse
堆垛起重機 stacking crane
帶式輸送機 belt conveyor
推土機 bulldozer
牽引車和拖車 tractor and trailer
牽引鏈 drag chain
單元化運輸 unit-load handling
單斗挖掘機 single bucket excavator
單斗裝載機 front loader
散狀物料 bulk material
絞車 winch
給料機 feeder
塔式起重機 tower crane
裝載機 loader
跨車 straddle carrier
運載橋 unloader
電動葫蘆 electric hoist
電梯 elevator
輥子輸送機 roller conveyor
橋式起重機 over head travelling crane
輸送帶 conveying belt
鋼絲繩 wire rope
龍門起重機 gantry crane
螺旋輸送機 screw conveyor
翻車機 car mper
鏟運機 scraper
懸掛輸送機 trolley conveyor
礦井提升機 mine hoist
礦車 mine car
纜索起重機 cable crane

❿ 求機械部件專業詞彙翻譯

Spindle core
Large steel screws and small bushes handle key. Hat. Steamed bread tooth spindle 18 teeth 7 sector gears. BBK chain. Flat chain. The angle and base 11 knife rack ( whole ) 12 needle knife ( true ) 13 press-needle frame needle needle pick press 14 to angle frame 16 pressure pressing needle delta 17 bushing 18 hat Gellar hook 20 small ring ( 3 ) 21 tappet 22 backpack drum retractor 23 Baishou 24 handle 25 stay 26 small support plate 27 supporting plates 28 sinker steel screw 29 syringe needle spring spring 30 pick 31 horse bird spring 32 shuttle spring 34 line clamper 35 shell fender triangle 36 chunks of tofu 37 chain frame 38 Ma bird frame 39 small supporting board in 40 super needle knife 41 needle knife about 42 to 43 packs of 44 roller angle of insurance support plate in hand 45 shuttle head 47 steamed bread 48 chain wheel shaft 49 grams of health cover 50 chain wheel .30 teeth 52 electromagnetic valve 53 solenoid valve Shou word stand 55 feet. Flexible wire