Ⅰ 跪求一篇关于机械类的外文文献附带中文翻译~~
You will learn about the effect of mold cooling, position of cooling channel, and cooling method for each part.
The temperature of a mold has a great impact on molding.
For example, if the temperature of the mold is too low, molten plastic will not flow smoothly through the runner or the gate, thus may not fill up in the cavity.
On the other hand, if the temperature is too high, it will take too long to cool down and solidify the molten plastic, so the molding cycle will be longer.
Therefore, by controlling the temperature of the mold, the following effects can be expected.
Molding cycle can be shortened by recing time for cooling and solidification of molten plastic.
The surface quality or measurement accuracy of parts can be improved by better mold ability.
Warp or stress in a part can be avoided that is caused when mold shrinkage varies e to different thickness, leading internal stress difference.
Effective mold cooling is done by pouring cold water into the mold through a cooling channel.
--------------------------------------------------------------------------------
Let''s see the detailed explanations of a cooling channel.
--------------------------------------------------------------------------------
Position of Cooling Channel
To effectively cool down a mold, decide on a position of the cooling channel considering the following remarks.
Adjust the mold temperature by pouring a large amount of water having a temperature close to the temperature required for molding.
Increase the number of the cooling channels rather than enlarge the diameter of one cooling channel.
Make sure to cool a cores (insert) which are difficult to cool, such as a thick core, a large size slide core, or a loose core.
Use mold material that has high heat conctivity to improve effectiveness of cold water.
--------------------------------------------------------------------------------
Cavity Cooling
Position a cooling channel as shown in the figure below for cavity cooling.
Since the numbers shown are for a general case, it is necessary to consider the position of a cooling channel according to molding material, molding shape, or mold material type.
Also, the cold water should flow from where the temperature of molten plastic is higher (closer to the gate) in the same direction as the molten plastic flows.
Example of 2 dimensional cooling channel
Pour cold water over the top side of parts.
Example of 3 dimensional cooling channel
Pour cold water to wrap parts.
--------------------------------------------------------------------------------
Core (Insert) Cooling
The cooling methods of core (insert) are listed below:
If the core is too small for a cooling channel to go through:
Cools down the core by inserting a copper rod or heat pipe that is highly efficient in heat conction into the core and then cooling down the copper rod or heat pipe.
If the core is large enough to go through a cooling channel.
Cools down by jet method in which cold water is flushed through a pipe attached to the channel.
Regular core cooling:
Cools down by baffle method in which a dividing plate is attached in the cooling channel on the core and cold water is poured to cross over the plate.
If there is a large cooling channel in a core:
Coolds down by inserting metal fittings in the cooling channel and pouring cold water in a spiral stream.
If the core is too small for a cooling channel or heat pipe to go through:
Make a core of beryllium copper and cool it down.
Ⅱ 急！关于机械类的数控加工的工艺方面的外文参考文献翻译。原文+翻译。
外文文献有，来翻译没有，翻源译得靠你自己了，如果需要直接网络Hi中留言同时贴出问题的链接地址和邮箱地址即可，希望能满足你的需要，能帮到你，并请及时知道评价，多多给点悬赏分吧，急用的话请多选赏点分吧，这样更多的知友才会及时帮到你，我找到也是很花时间的，并请及时采纳
Ⅲ 求机械类外文文献，毕业设计要用的英文文献。
出处的母语是英语的人写的期刊或者户
对待好的
Ⅳ 求机械专业外文资料，文献
这也太宽泛了吧，机械哪方面的呀。Google学术、知网会有
Ⅳ 求机械类英文文献
机械类英文文献有翻译 机械零部件、机构、装置、设备设计、制造及..
读机械的英语不好回翻译答好!现在传点资料上来给大家分享下!希望大家支持,已经有中文翻译 muzili83 2007-05-09 09:48...可惜,是材料类的,用不上 唉~~ candiwell 2007-05-10 08:55 很好的,请问楼主可有关模具方面的,最好是冲压拉深...
www.jxcad.com.cn/simple/index.php?t301187 ... 10K 2008-2-26 - 网络快照
www.jxcad.com.cn 上的更多结果
Ⅵ 机械制造的外文文献
自己学校网站有的